How to measure a wheels PCD
How to Measure Wheel PCD (Pitch Circle Diameter)
PCD (Pitch Circle Diameter) is the diameter of the circle that passes through the centre of all wheel studs. It’s used to match the correct hub, disc, drum, or wheel to your trailer.
Important: Accurate measurements are critical. Measure centre-to-centre (not edge-to-edge), and use a vernier caliper if possible.
What you’ll need
- Vernier caliper (best) or a quality ruler/tape
- A clean hub face so you can clearly see stud centres
- Pen + paper (or use the quick formulas below)
Measure your stud pattern (4, 5 & 6 stud)
In the diagrams below, A = centre-to-centre distance to the nearest neighbouring stud. B = centre-to-centre distance to the furthest stud across the hub.
4 Stud
Source method: AL-KO “How to measure a PCD”.
5 Stud
Source method: AL-KO “How to measure a PCD”.
6 Stud
Source method: AL-KO “How to measure a PCD”.
Common stud patterns (quick reference)
Stud pattern is commonly written as “number of studs × PCD”. The table below lists common PCDs and stud threads referenced in the AL-KO chart.
| Common Name | Stud Pattern (as written) | PCD (mm) | Typical Stud Thread | Common Thread Options |
|---|---|---|---|---|
| Ford | 5 × 4.5" | 114.3 | 1/2" UNF | |
| Commodore | 5 × 120mm | 120 | 7/16" UNF | 12mm |
| HT | 5 × 4.25" | 108.0 | 7/16" UNF | |
| HQ | 5 × 4.75" | 120.65 | 7/16" UNF | |
| Gemini | 4 × 100mm | 100 | 7/16" UNF | |
| Honda | 4 × 100mm | 100 | 7/16" UNF | |
| Datsun | 4 × 4.5" | 114.3 | 7/16" UNF | |
| 5 stud LCR | 5 × 150mm | 150 | 9/16" UNF | 14mm |
| 6 stud LCR | 6 × 139.7mm | 139.7 | 1/2" UNF | 12mm |
| Nissan | 6 × 139.7mm | 139.7 | 1/2" UNF | 12mm |
| Range Rover | 5 × 6.5" | 165.1 | 5/8" UNF | |
| Ford F100 | 5 × 139.7mm | 139.7 | 1/2" UNF | 12mm |
| Bedford | 6 × 205mm | 205 | 7/8" UNF | |
| Land Rover Defender | 5 × 6.5" | 165.1 | 5/8" UNF | |
| Land Rover | 5 × 6.5" | 165.1 | 5/8" UNF | 9/16" UNF |
| New Navara, Nissan | 6 × 114.3 | 114.3 | 1/2" UNF |
Tips to get the right result
- Always measure from centre of stud to centre of stud.
- If stud centres are difficult to locate, measure the outside-to-outside distance across the two studs along the line joining their centres, then subtract one stud diameter, provided both studs are the same diameter. Do not subtract a stud diameter when measuring between corresponding edges on the same side of each stud.
- Repeat the measurement twice and average it.
- Write your result as: (stud count) × (PCD) e.g. 6 × 139.7.
Ready to Choose Your Wheels?
Use your stud count and measured PCD to narrow down our Wheels & Tyres range. Matching the stud pattern is only one fitment check; confirm the wheel's other specifications against your trailer before ordering.
Not sure which option to choose? Contact us with your stud count, measurements, existing wheel markings and a photo of the hub and wheel so we can help check the options.
Measurement method and reference table adapted from AL-KO “How to measure a PCD” guide.