AL-KO Trailer Bearing Kits: Parallel vs 2 Tonne Replacement Guide
Choosing between AL-KO’s Parallel and 2 Tonne bearing kits is a fitment decision, not simply a choice between two load ratings. The kits use different inner and outer bearing combinations, and the seal and grease cap also need to match your hub.
This guide compares two specific products: the AL-KO 484501 Japanese Parallel kit and the AL-KO 487001 Japanese 2 Tonne kit. It is not a complete catalogue of every AL-KO bearing family.
If you have not identified the existing bearings yet, start with our trailer wheel-bearing identification guide. That explains how to record the inner and outer cone and cup numbers. This article helps you compare kits once you have those details.
Quick answer: which AL-KO kit should I compare?
Compare 484501 if your hub requires the Parallel arrangement with LM68149 cones and LM68110 cups in both inner and outer positions. Compare 487001 if the required arrangement is HR30210 inner and 15123/15245 outer.
Neither bearing combination is a complete fitment confirmation on its own. Check the exact bearing markings, seal arrangement, grease-cap fit and supplied contents before ordering.
AL-KO 484501 vs 487001: key differences
| Check | 484501 Parallel | 487001 2 Tonne |
|---|---|---|
| Product | AL-KO Japanese Parallel bearing kit | AL-KO Japanese 2 Tonne bearing kit |
| Inner bearing arrangement | LM68149 cone / LM68110 cup | HR30210 |
| Outer bearing arrangement | LM68149 cone / LM68110 cup | 15123 cone / 15245 cup |
| Nominal inner / outer bearing journals | 35 / 35 mm | 50 / 31.75 mm |
| AL-KO catalogue capacity designation | 1,600 kg per pair | 2,000 kg per pair |
| Key seal check | Parallel-profile seal; nominal 43.9 mm seal journal in AL-KO’s profile reference | Correct standard or marine seal arrangement; nominal 60.3 mm seal journal in AL-KO’s profile reference |
Journal dimensions are manufacturer reference dimensions for the profiles, not a substitute for confirming the exact supplied parts. Record bearing suffixes as marked and ask for confirmation if the replacement reference differs.
What does “Parallel” mean in this comparison?
The Parallel arrangement shown here uses the same bearing combination in the inner and outer positions. In AL-KO’s profile reference, both bearing journals are nominally 35 mm.
That does not make it interchangeable with a Slimline kit. For example, AL-KO’s Slimline profile uses different inner and outer bearing combinations even though its inner bearing reference can look familiar.
Compare both bearing positions. Finding LM68149 on one bearing is not enough to identify the complete kit.
What makes the 487001 2 Tonne kit different?
The 487001 listing specifies an HR30210 inner bearing and a 15123 outer cone with a 15245 cup. AL-KO’s profile reference shows different nominal journal diameters for the inner and outer positions: 50 mm and 31.75 mm.
A reference to “50 mm” alone does not establish fitment. You still need the outer bearing, hub machining and seal arrangement to match.
Likewise, a 12-inch brake drum or a 2-tonne axle description does not identify a bearing kit by itself. Use the actual hub and bearing specification.
Do the capacity labels tell me how many hubs a kit services?
No. AL-KO’s catalogue describes 484501 as 1,600 kg per pair and 487001 as 2,000 kg per pair. That capacity wording does not mean one retail pack contains the parts for two hubs, and it is not a per-hub rating.
Use the contents list to determine how many packs you need. The current 484501 listing specifies two cone-and-cup assemblies, a seal and a cap. Those two bearings occupy the inner and outer positions of one matching hub; they are not two complete hub-service sets.
The current 487001 contents list specifies one inner assembly, one outer assembly, one seal and one cap. Confirm the quantity needed for every hub being serviced rather than ordering from the capacity label.
Fitting a bearing kit does not, by itself, upgrade the approved capacity of the axle or trailer. Complete-assembly limits still apply.
Check the seal separately from the bearing bore
The bearing journal and seal journal are different parts of the spindle. A 35 mm bearing bore, for example, does not imply a 35 mm seal running diameter.
For the Parallel profile, AL-KO lists a nominal 43.9 mm seal journal. Its 2 Tonne reference lists a nominal 60.3 mm seal journal, with different standard and marine seal arrangements.
Those profile references do not establish the exact seal included in a retail pack. Confirm the seal part number or its dimensions and construction against your existing hub and spindle before ordering. If the supplied seal needs clarification, ask us to confirm the pack.
Do I need a standard or marine kit?
AL-KO lists separate standard and marine kit references, including 487001 and 487002M. Do not assume that similar bearing numbers mean the complete kits are interchangeable.
The seal arrangement is an important check. A boat-trailer application should be matched to the exact hub and spindle specification rather than selecting solely because a product name includes “marine”. Have the servicing technician confirm the required combination.
Check the grease cap and pack contents
A grease cap must fit the hub’s cap housing. Do not infer that dimension from the bearing bore or seal size.
The 487001 listing describes a DC2-style cap, and AL-KO lists that cap family for a nominal 63 mm housing. Confirm the actual hub and supplied cap before treating it as a match.
Before checkout, verify the number of cones and cups, seal type, cap and any separately required retaining parts. Do not assume grease, a nut or a split pin is included unless the pack description confirms it.
Before-ordering checklist
- Inner bearing cone and cup numbers, including suffixes.
- Outer bearing cone and cup numbers, recorded separately.
- Hub or axle identification and existing kit reference, if known.
- Seal identification, dimensions and standard or marine arrangement.
- Grease-cap housing and cap fit.
- Confirmed pack contents and number of hubs being serviced.
Have dismantling, inspection, fitting and bearing adjustment carried out using the manufacturer’s service procedure by a suitably qualified technician. This comparison is not an installation guide.
Frequently asked questions
Will either kit fit any AL-KO axle?
No. AL-KO supplies several bearing profiles. Match the complete bearing, seal and hub arrangement, not the brand alone.
Can I identify the kit by wheel stud pattern?
Do not rely on that. The wheel pattern does not establish the hub’s bearing machining or the spindle profile.
Is the higher-capacity kit an upgrade for my existing hub?
Not automatically. These kits have different bearing arrangements. A higher catalogue capacity does not establish dimensional compatibility.
Compare the two AL-KO kits
Check the 484501 Parallel bearing kit or 487001 2 Tonne bearing kit against the details recorded from your hub.
Need help choosing? Send R&M Trailer Spares clear photos and readable numbers for the inner and outer bearings, cups and seal, plus the hub identification and cap measurement. We can help narrow the selection before you order.
Technical references: AL-KO bearings reference, axle and stub-axle profile chart and AL-KO Authentics parts catalogue.